Category Archives: Designers & Builders

La Rosa – Flashback

Posted on by
7

LA ROSA – FLASHBACK


I just love opening the WW email inbox, particularly when out of the blue you get a treasure trove of photos on a boat that you know but do not have much content from her past.The other day Alan Duckworth contacted me to say he came across the WW site while searching for new photos of the 1923, Ernie Harvey built launch – La Rosa. Bob King, who owned the vessel for 50 odd years and significantly modified the ketch, was Alan’s grandfather. 

The above gallery of old photos are from Bob King’s ownership period. Alan recalls that the motor was a Lister, compression start, that could run for hours on bugger all fuel.


The current owner of La Rosa – Ward House will love the photos – hopefully his good friend Baden Pascoe will alert him to the story. You can see and read more about La Rosa at the WW links below:
https://waitematawoodys.com/2013/04/16/la-rosa/
https://waitematawoodys.com/2014/02/27/castaway-la-rosa-on-the-slip/

Input below from Mark Erskine

“I was interested to read about La Rosa and what a wonderful antique engine she has.

I see “Graeme” posts the engine is a 26 HP Lister HW2, but it is a Lister JP2M.

The JP2M specs are: Capacity: 2,868cc. / HP: 21 @ 1,200rpm. / Weight: 2,576 lbs/1.168 tonnes

https://www.stationaryengineparts.com/Lister-Petter-Engine-General-Specs/

They were made from 1936 and 1954 apparently (haven’t been able to confirm), so it would be interesting to see if the owner knows the age of the engine.

Like all of the old Lister / Petter water cooled range of engines, the JP2M is built so big and heavy and runs so slowly that if properly serviced, maintained and used, it should never wear out in marine use 😁 “

https://www.marinepowerservices.co.uk/engines/past-engines/90-1952-lister-jp2m

https://waitematawoodys.com/2019/12/01/wooden-boat-bureau-advice-for-buyers-and-sellers/

Katoa

Posted on by
Reply

KATOA
The photos above of the 37’7” launch Katoa , were sent in by Bay of Islands woodys – Dean Wright. Dean snapped Katoa in the Te Puna and Kerikeri Inlet area last week.

Designed and built by Geoff Bagnall in 1988, she may by ‘youngish’ for a woody but she is an oldie at heart 🙂 Powered by a 130hp Lees Ford diesel.


Katoa has appeared on WW before – link below for a peek-down-below. https://waitematawoodys.com/2019/06/19/katoa/

DONATE HERE https://givealittle.co.nz/org/nztbs

A Woody Christmas – A Time For Giving

Posted on by
Reply

A Woody Christmas – A Time For Giving

I have an ask today – one of wooden boatings coolest and most deserving organisations urgently needs help – relax, you don’t need to do anything other than put your hand in your pocket – more on that later. But first let me tell you about the New Zealand Traditional Boatbuilding School – it was started back into 2005 by a group of visionary wooden boat enthusiasts. I have rubbed up against it a lot over the years – during the re-birth of the classic wooden launch movement we used their facilities for social gatherings and seminars. I have even done boat maintenance workshops and built a woody tool box (under close supervision)If ever there was something that deserved its place in our maritime community – it’s the NZTBS, more so than a lot of other questionable entities that live off rate payer handouts.I won’t bore you today with the day to day challenges the current trustees have keeping the doors open – just trust me when I say – to survive the short term they need help, mid term hopefully they will be able to secure sponsorship.


Today’s WW story is an example of the amazing work the school does – last week, trustees Olaf Wiig (classic launch – Lady Margaret and Alan Hooper (spirit of tradition launch – Katherine) ran a pilot course for one they are hoping to offer in the future. In a joint venture with Taikata Sailing Club, Drowning Prevention Auckland and Coastguard Education, NZTBS ran a week long course for a group of 9 year olds, building a pair of John Welsford Scraps dinghies. The whole week was a great success, resulting in two cool little boats being launched on Saturday. Just check out the looks on the kids faces – you don’t get that from playing on an electric device. The kids all made a name board for their boat and then voted for the best names and then Moonlight and Rose Gold were christened and launched – so cool.

Special thanks to James Hutchinson and Olaf Wiig for the photos
HOW CAN YOU HELP

The NZTBS is a charitable trust – donations are eligible for a tax credit and its so easy – click on this link and invest in the future of wooden boating in New Zealand. And do you know what?, you’ll feel good about it 🙂

https://givealittle.co.nz/org/nztbs
Merry Christmas & Thank You. alan houghton – waitematawoodys founder

Classic Wooden Small Boats

Posted on by
2

Classic Wooden Small Boats
In the days before remote controlled model yachts – the yachts were divided into two kinds – Free sailing – were boats were sailed in open water and ‘chased’ by their skippers in dinghies who ’touched’ the yachts during the course of the race to adjust their course.

The other kind was – Pond yachts, sailed on small lakes, basins or special ponds (in parks), the skipper would race around the pond to tack or gybe the model as it got close to shore. Refer b/w photos below for examples of the racing.

The top colour photos were sent to me by an ex work colleague – John Maxwell, we worked together over 30 years ago in the crazy world of advertising in the late 1980’s. Unknown to me, one of John’s passions is the building of old style pond yachts, but with a modern take, refer examples above of Ranger, Innismara, Infidel, Meter class (black hull) and one in the vein of an A class. Not exactly accurate, but instantly recognizable as the original. They are all hand painted, so as to faithful to the old style. John commented that the problem with making the models sail, is that the depth of the keel, mast position/ height etc, have to be altered slightly from the plans of the real boat, otherwise it just sails sideways or rounds up into the wind. John aims to capture the spirit of the original, but still maintaining the ‘Old school’ charm of the yesteryear pond yachts. They are all free sailing models and quite big ie 1.8 m long. Typically they have a lot of lead on the keels approx 15-20 lbs., most are balsa over wooden frames with glass over the top. 
Stunning work – but it doesn’t surprise me, John was / is a very talented man, and rather good with a paint brush and canvas.

Ngapuhi (Waihou)

Posted on by
1

NGAPUHI ( > WAIHOU)

DOES ANYONE KNOW A ROSS DIXON (or Michael Adams) previous owners of the launch Menai – if so could you ask that they contact me on waitematawoodys@gmail.com

Ngapuhi was built by Brian Lane in 1952-3 as a towing launch for Lane & Sons (Timber Millers) at their premises in Totara North, Whangaoa Harbour. Originally named Waihou. Purchased by Northland Port Corporation in 1963 her name was changed to Ngapuhi & she served as the pilot boat for the Whangarei Harbour Board for 35 years.

During 1983-4 an extensive refit was carried out when a larger aluminium wheelhouse was added. The original 2x GM471 engines were replaced with new 6LXB Gardners, propshaft angles modified, and larger rudders made to suit the new engine installations.

Has been in current ownership since 1998 during which time was chartered back to Northland Port until 2000 & kept in SSM survey for 16 passengers until late 2013 when the SSM regulations were changed.

While based in Whangaroa her owners have completed numerous trips to the Three Kings, Waitemata, Gt Barrier, & also used to view the racing the last time Team NZ hosted the America’s Cup in Auckland.

Details below:

Length 13.84m Beam 3.70m. Draft 1.07m. Reg tons 22.

Engines 2x 6LXBM52 Gardner 1984. Diesel Engines governed to 1500RPM, 127 HP continuous rating.

Gear boxes Twin Disk 1.45-1

Fuel Capacity 1400 litres Water capacity 200 litres

Max speed 11 knots at governed rpm. . Cruising speed 8-11 knots. . Fuel consumption approx. 25 l/h @ 11 knots, approx. 18 l/h @ 8 knots.

Hull construction. Carvel plank Kauri over laminated frames of 70x40mm @ 250mm centres.

Other features. Icom VHF, Furuno GPS plotter/sounder, walk in engine room with fan forced ventilation. F’ward and aft cabins, galley, separate toilet with holding tank, wash down pump, 2x sets of fixed manual & electric bilge pumps & other safety equipment to meet previous survey requirements. Currently 3-4 berths, easily expandable to 6-8.

Thanks to Ian McDonald for bring the tme listing to the attention of WW.

Opua Marina / Hardstand Mooching

Posted on by
3
Luana
Florence
Ngapuhi
Typee
Sea Mate
Unknown

OPUA MARINA / HARDSTAND MOOCHING
Woody Dean Wright snapped the above selection of woodys that he spotted at Opua at the weekend.I have supplied links to previous WW stories below. I know I’m a broken record, but Luana …………. 🙂
Luana    https://waitematawoodys.com/2016/04/01/luana-4/

Ngapuhi – Ex pilot boat, more on this one later in the week

Florence.  https://waitematawoodys.com/2017/12/28/florence-6/

Typee.   No details known

Sea Mate (Birdsail 52 on the marina) – No details known 


Dean didn’t catch the name of the ‘long’ keeled yacht in the last photo above – any one able to supply details?

Input from Neil Chalmers – Could be ‘Restless’  – Lou Tercel  / John Alden   April 1920.

Input from Simon Smith – The long keeled yacht is indeed the Tercel yacht Restless. 100 years old and owned by Russell resident Tim Beattie who being a master painter has her in beautiful condition. Always sails in the Tall Ships Race but with her ocean cruising rig needs a strong breeze to show her mettle.

Chantal – Sailing Sunday

Posted on by
3

Chantal – Sailing Sunday

Chantal was designed, and built in 1981, by Denis Brown, in the Bay of Islands. LOA 8.24m, DWL 7m, Beam 2.1m, Draft 0.9/1.9m Displ 2,450KG 

A 3/4 rig, double ended, centreboard, sloop, that is easy to sail single handed, and very quick in light air. Great for cruising, as the shallow draft with the board up, gives you more options for exploring and anchoring. Fun to race as she is pretty efficient up wind, and has very low drag on a reach. Sailing photos taken during the 2017 Tall Ships Classic Invitation Race.

Constructed in Radiata Pine and Kahikatea, opposing diagonal 4.5mm laminated  planking, outer sheathing 5mm lamination longitudinal. Everything well soaked in West System Epoxy. Centrecase fabricated in 6mm mild steel plate, which holds 1200KG of lead ballast. Centreboard is solid Kauri. Shaft tube and bearing setup for a small inboard motor, which we installed back in 2000 and removed again in 2001.

Sleeps 4 comfortably, and while space is fairly tight the arrangement feels generous. Single burner gas stove, storage space for a medium sized chilly bin and jerry cans for water. Torches and candles for lighting, and a chemical toilet. A very simple set up.

(details & photos ex owner – Bruce Mitchinson)

WIN AN OFF CENTER HARBOR CAP

All correct answers to the question below, go into the draw to win an OCH cap. Enter via email only at waitematawoodys@gmail.com Closes 8pm 13-12-2020

Q – Name Bruce Mitchinson’s classic launch

SCROLL DOWN TO YESTERDAYS STORY – STARTED OFF WITH ONE OLD PHOTO, MORPHED INTO AN AMAZING RESTORATION STORY 🙂

Wooden Boat Yard Mooching

Posted on by
2

Wooden Boat Yard Mooching
Hobsonville woody John Wicks sent me a bunch of photos yesterday from this home marina at Hobsonville. It reminded me that I had snapped a few myself on a recent visit, nice to see that the woodys had moved along and should be re-floating soon.First up the Athol Burns designed, Barney Daniels built – Taotane, which John commented – was being brought back from the almost dead. Then we see the very regal Lady Crossley, the 1947 Colin Wild motor-lunch, out of the shed after a lick of paint and varnish.Lastly above the 48’, 1948 Lidgard built Ranui , in for a paint job, and wearing my Wooden Boat Bureau cap – I have to remind you that she is for sale and ready for summer cruising. More details here

https://waitematawoodys.com/2019/07/08/ranui-a-peek-down-below/


Things are getting a tad posh at The Slipway Milford, when I hauled out the other day, instead of a ladder, a set of stairs was waiting for me – much appreciated 🙂

Marline Back In The Water

Posted on by
3
Builders son – Ken Warne at the helm
Post launching – photo ex Max c/o The Slipway Milford

Marline Back In The Water
Back in mid September we reported that the 35′ Leone Warne built – Marline was tucked up in the shed at The Slipway Milford getting a top-chop and the biggest dose of TLC ever. You can read and see photos from the process and lots of historical photos here https://waitematawoodys.com/2020/09/14/marline-gets-a-top-chop/


Last week Marline was quietly slipped back in the water looking rather cool with her back to the past make-over. I have seen a photo of her looking like Huia Falls after being hauled out after a brief – “have we got the waterline right” dip. But she went back in and 24 hours later the flow had abated. Below photos show her as launched and prior to the haircut.

16-05-2025 UPDATE ex CMC DESIGN – MARLINE out for some TLC prior to her 75th birthday later this year. As covered before she was built by Leon Warne in 1950 and to this day remains in the Warne family ownership.

Rawene

Posted on by
Reply

RAWENE
When I was catching up with lan Craig re yesterdays story I gave him a wind up re how hopeless he was at keep us updated on the work in his Lake Rotoiti boat yard. Seems the dig in the ribs worked as a few hours later I received the photos above of Rawene, taken from Waikeremoana when Alan went  down in February 2020 for some repairs on Rawene. The boat was hit on her mooring and broke a few ribs.The old photos below are on the wall in the store there.

It has been commented on WW that she was built in 1928 by L.C. Coulthard. Read & see more about her here https://waitematawoodys.com/2017/12/14/rawene-a-peek-down-below/