Earlier in the week one of the WW spotters, Alan Sexton, dropped WW a note to say that the 44′ Oliver & Gilpin 1964 built classic wooden launch NAUTILUS was hauled out at Sandspit Marina for some TLC. Always good to see the big old girls being looked after. My lips are sealed but NAUTILUS is another classic woody owned by one of NZ’s yachting ‘royalty’.
The first grouping of photos is as of this week, the b/w photo is probably as launched, and the last lot are from approx. 4 years ago + a peek down below (again 4>5 yrs ago). Forward motion is via twin120hp Isuzu diesel engines.
We understand home these days is the Whangateau area.
The brief was for a Jason Prew Paint Job and to overhaul her running gear (driveshaft, props etc), well as is almost always the case the shopping list grows and approx. 9 weeks later MARINUS was re-launched yesterday.
The most visible highlights being her new colour and the removal of the 2 lower portholes.
LOOKING FOR INFORMATION ON – CLASSIC LAUNCH – COLUMBIA
Recently WW was contacted by Richard Erdman who had just finished re-reading 2 books penned by Ralph S Von Kohorn that document Ralph’s circumnavigation of the South and North Islands of New Zealand in the early 1970’s aboard his motor vessel COLUMBA. Richard commented that COLUMBA was designed in 1967, 45′ loa, and powered by a single Detroit GM 283, 8 cylinder engine, that gave her a top speed of 15 knots but she cruised at 9 knots. No mention was made of the vessels designer or builder.
The books were published : South Island cruise – Jan 1977 and North Island cruise – Jan 1979
In 1977 Ralph was commodore of the Mana cruising club in Wellington.
The artist painting of COLUMBA on the North Island book has been very generous in their rendering i.e. she looks better than in real life (South Island cover) 🙂
So woodys todays question is what became of COLUMBA and can we earn more of her back story.
INPUT EX ALAN SEXTON – A very detailed description of Columbia is provided in Appendix II in “Columbia Cruises North”. Quick summary, designed by Jim Cole (California), built by Lidgards, 2 skin kauri , powered by Detroit 8V53, launched 1967. Baron Ralph Steven von Kohorn died in early 2011 aged 91, his wife Jill died some months later aged 67.
INPUT EX JEFF GIDDEN – Used to be moored under the bridges at Paremata many years ago.
INPUT EX BOB SPEARMAN – Columbia is in Havelock, Pelorus Sounds
26-06-2025 INPUT EX SANDRA GIBSON – The Columbia has been restored by Stanford boatbuilders, as she had been gutted. She is now powered by a V8 cat and she is 2 meters longer. Cruises at 14 knots. Modernized inside and very comfortable
CLASSIC WOODEN BOAT RIVER CRUISE – TRIP REPORT Fridays Classic woodys cruise to the waterfront Riverhead Tavern for lunch was a grand day afloat, 13 classic wooden craft made the journey up the upper reaches of the Waitemata Harbour to the historic tavern. It was extra special with several first-timers making the trip. We were blessed with the weather and also having just one of the tourist ferries making the trip on the day, which allowed us to berth a lot of the boat on the jetty.
Special mention to the 7 classic launch skippers and partners that came by water taxi (MY GIRL) – Cam Malcolm (Connie V), Rodger Moore (ex Te Hauraki), Jason Davies (Lucinda), and those via car – Ian Gavin (Florance Dawn), Matt Cooper (Korawai) and John Chambers (Ngarunui), Murray Deeble ( Waikiore) combined with the 13 boats on the water we had crews from 20 classic craft present on the day. Very happy with that turn out.
True to form, the tavern and its staff extended their usual warm hospitality. Enjoy the photo gallery
Todays photos come to us from John Dawson. We learnt more from an online search that popped up an old fb comment by Ray Morey where Ray told us OWAKA was built in 1927 by Collings & Bell in Auckland for service at Lyttelton.
Ray also said that in the mid 1930’s she was re-powered with a Kelvin K9 engine. Then in the mid 1960’s she was re-powered agin with a D-Series Ford.
In another fb post Lew Redwood tagged the top photo above as being c.1950>69 and the location being Honeymoon Bay, Moturua, Bay of Islands (photographer – Ron Clark).
CLASSIC WOODEN LAUNCH – DONALD SUTHERLAND (MV USSCO / SEA HAWK) – On The Move
The 46’ classic wooden launch – DONALD SUTHERLAND, once named MV USSCO and also SEA HAWK, was spotted by Angus Rogers at Half Moon Bay Marina, Auckland on Tuesday on the back of a Boat Haulage rig.
We last saw her back in May 2023 when she had had an oops in a storm and ended up on the Tamaki Drive breakwater, as shown in the second group of photos. She has made several appearance on WW, links below.
In the previous WW stories we learnt she was built by Collings & Bell in 1936 and commissioned by the NZ Government as a tourist / passenger vessel, also worked as a light house tender.
Not sure from the photos she is coming or going, I suspect leaving HMB as you dont need a transporter to launch + the ‘Kaiapoi’ name on the stern suggests she’s heading to the Christchurch region.
Back in April 2023 we got to have a gander down below on the 1946 classic wooden launch – MARINUS. A link to that story below. As you will see MARINUS has one of the smartest looking interior in the woody fleet. https://waitematawoodys.com/2023/04/17/marinus-a-peek-down-below/
46’ in length she was designed by A Deeming and built by Barr Brown in Wellington.
In late April when helping relaunch Angus Rogers CENTAURUS, MARINUS was the next up the slipway.
Lots of TLC happening but the two projects that meet with my approval are:
1. The two lower portholes have been removed
2. The chosen colour of her Jason Prew Paint Job (JPPJ) – we kiwis are very boring in our chosen hull colours eg white>>>>>
You only have to look at the classic wooden boating movement in the USA for inspiration – well done to the owner for making the call.
And there’s another woody hauled out on the #3 slipway thats going to sport a splash of colour – details soon.
AN INSIGHT INTO NZ’S UNIQUE MARINE ENGINES – Part Seven Todays WW story follows on from earlier stories – link below to Part One, Two, Three, Four, Five and Six As per pervious stories in the series the content has been pulled together by Ken Ricketts and ‘polished’ byPatrica and Ken’s daughter Corinne Pettersen. As always we have endeavoured to be as factual as possible but there will always by matters others will either know more about or be able to correct errors – so woodys do not hold back in commenting.
THETIS with her twin Graymarine 4 stroke 6cyl diesel engines
These are a very rare model of the Graymarine range, that was originally produced in WWII for the US military. All Graymarine diesel engines for general and normal marine use worldwide, including NZ, are based on the GM Detroit two-stroke engine, marinized by Graymarine. I believe the THETIS engines were the only two that ever came to NZ and were specially imported by Jack Butland for his 1955 Lane Motorboat built launch, THETIS. Here is a copy of previous comments I made regarding these engines, on Woodys.
“Ken Ricketts reports that having recently spoken with Thetis’s owner that the 2 in line, 6 cyl, 4-cycle, 120hp Gray Marine engines, installed in 1960 (still there today) are a very rare model & type. They were manufactured during WWII for the American forces & could possibly be the only 2 in NZ. The owner believes her original owner Jack Butland in the later 1950’s probably reconditioned, & war surplus imported them.”
BELOW IS A REPRINT OF THE HERCULES SETION IN PART 2 WITH ADDED TEXT I HAVE TAKEN THE LIBERTY OF REPRINTING IN THE CIRCS.
HERCULES 6 CYL c100HP DIESEL ENGINE AS FITTED TO THE FAYE
HERCULES 275 HP DIESEL ENGINE, SIMIALAR TO THAT PREVIOUSLY IN THE RAKANOA
FAYE WITH HER 6 CYL HERCULES HOME MARINISED DIESEL ENGIINE
RAKANOA WITH HER 275 HP 6 CYL. MARINE/HOME MARINISED DIESEL ENGINE
Hercules was a manufacturer and supplier of a large number of basic engines to many marine engine companies for marinization by each company to its own specifications. This included names such as Kermath, Chrysler, Graymarine, Scripps, Chris Craft, and many more. However, engines sold under the Hercules name, based on my research, are comparatively very small compared to their total manufactured units.
There are two boats I know of in New Zealand that have engines both labelled under the Hercules name and are diesel engines. One is the FAYE, which is equipped with a home-marinized C100P 6-cylinder Hercules diesel engine. This engine replaced her original Willys Jeep petrol engine when she was about 4 or 5 years old. FAYE’s details are noted in her Willys Jeep listing in part 2 of this post.
The other is the beautiful 56-foot RAKANOA, built in 1946–47, which had a 6-cylinder 250HP Hercules diesel fitted after she had been in the water for one year. This engine replaced her original GM Detroit 165HP 6-71 diesel.
Her original owner, Stan Parker, was a brilliant engineer and owned a very large precision engineering business.
I am not sure if the Hercules engine was factory or home-marinized, as he would certainly have had the ability and equipment to do this. Stan, the original owner of RAKANOA, owned a large heavy engineering factory in Auckland. This business passed to Ross when his father passed away in 1961. RAKANOA retained this engine until 1981. Ross told me, after he inherited her many years ago, that they had always had trouble starting the Hercules engine, especially when hot. Many years after he inherited her, he eventually replaced the Hercules with a Gardner 6L3 diesel engine, which she still has to this day.
The Hercules engine was fitted because original owner Stan P., could not tolerate the very loud high pitched geartrain noise of the Rootes blower, combined with a loudish exhaust noise, she had with the G.M. Detroit
Unfortunately, I have not been able to find on research to date, any images of the 250 HP marinised version of the Hercules engine, however I have found what may be an unmarinised version, of RAKANOA’s engine.
RUSTON HORSNBY DIESEL ENGINES.
HAIMONA ex MANGA, WITH HER ORIGINAL TWIN 6 cyl, FODEN DIESEL ENGINES
RUSTON HORNSBY TWIN CYLINDER MARINE DIESEL ENGINE AS USED IN THE MANOWAI
HMNZS MANGA AS ORIGINAL.
HAIMONA IN HER PLEASSURE CRAFT GARB WITH HER 2 RUSTON HORNSBY DIESEL 200HP ENGINES, ON THE KAIPARA HARBOUR
MANOWAI IN HER RUSTON HORNSBY DIESEL ERA, AT HERALD ISLAND
There are only two of these I know of in New Zealand in pleasure boats. One was in the 32 ft MANOWAI, during the second part of Claude Atherton’s era, from 1949 until at least the 1960s; it was a twin-cylinder version of the engines.
The other boat was HAIMONA, formerly HDML MANGA, which was based in the Kaipara Harbour. Eventually, after a few years there, the only slip she was able to use for maintenance became unavailable, and she deteriorated badly before being destroyed by her last owners.
When they bought her, a massive coaming structure was added, and they also replaced her original Foden engines with twin 200 HP 6-cylinder Ruston Hornsby diesels, which they removed prior to dismantling her.
FORD FALCON 4.1 LTRE 6 CYL. PETROL ENGINES
FORD FALCON 4.1 LTRE 6 CYL. PETROL MARINE ENGINE
VALSAN CHRISTMAS 1948 IN HER PRE-FORD-FALCON, PETROL ENGINE ERA
The 1938 Roy Lidgard-built VALSAN was bought by Arnold Baldwin around 1947, complete with her original engines, which were 2 x 100 hp flathead Graymarine petrol engines. He owned her for many years, and the time eventually came, after many of those years, when they had to be replaced, around 1970.
I was amazed that he chose 2 x Ford Falcon 4.1 L petrol engines as replacements, as these were engines usually associated with small day boats or runabouts, often equipped with stern drives or jet units. There were a total number of such engines unknown to me, and she is still the only launch I have ever heard of with these engines.
Things have, of course, moved on since then, and the last I heard, she had 2 x 4-cylinder Mitsubishi diesel engines post 2000.
CHRYSLER-MITSUBISHI CN-55TI 200HP 6CYL. IN LINE MARINE DIESEL ENGINES
THE CHRYSLER-MITSUBISHI CN-55TI 6 CYL. DIESEL ENGINES PRODUCING 200hp @ 3150 RPM INSTALLED IN ALIBI
ALIBI’s 2 “STERN POWER” STERN DRIVE UNITS, & NOTE BOTH ENGINES EXHAUST OUT THE SAME SIDE AT THE TUCK
As readers of this series may recall, ALIBI made a cameo appearance in part 2 when I was seeking information related to her sistership, which I now know is or was called CRESCENDO, seen below on launching day, as I have seen the two V8 Chrysler-branded diesels CRESCENDO had when new.
Thanks to the input of others, I have now also discovered that these engines were manufactured by another company, and simply sold under the Chrysler label, which seems to me to be a continuation of Tony Mason’s apparent tendency to use engines with the Chrysler label, as in ALIBI.
However, since the previous cameo appearance of ALIBI, I now have full details of her engines, thanks to a lady named Juliet Hindman, who is very knowledgeable about the Mason Clipper range of boats.
Her family has owned one of the two only 33-foot versions of the Mason Clipper, and she has now contacted me.
As a result, and with the information she has provided, ALIBI now definitely falls into the “Unique” class of engines category, as specified above, as far as I’m concerned, and she now has her place in the group in her own right.
ALIBI’S two CHRYSLER-MITSUBISHI CN-55TI DIESEL ENGINES, producing 200 HP at 3150 RPM, are driven through Warner gearboxes to “Stern Power” make, cream-painted counter-rotating outdrives. While the engines and gearboxes are both left-handed with a 1-to-1 ratio, outward turning counter-rotation of the propellers has been achieved by the gearing system in the stern drive units, which are also acting as reduction gears with a 1.5-to-1 ratio, driving Volvo 16 x 17-inch propellers.
I feel the engine-to-stern-drive setup with these engines, is superior to many others, in that the engines are obviously primarily produced for conventional drives, having the gearboxes attached to and as part of the engines, but can still be used either way, for stern drive units, or conventional drives, with the stern drives simply providing the drive to the propellers.
Many manufacturers combine the gearbox and stern drive into one unit, which makes them much more complex and quite possibly much more expensive to maintain.
Additionally, the combination drive/gearbox units are often very “clunky” and jerky when selecting forward or reverse, whereas there would not be this clunk with the smoothness of hydraulic engine-attached gearboxes.
I have spent a great deal of time, trying to source a good clear image of these engines, but they seem to have disappeared from historical public databases, and the only image I have been able to source, is of ALIBI’S own engines installed in her.
It is, however, wonderful that she still has these original engines after all these years since she was built in the later 1970s. A great testimony to Mitsubishi. Here are her details as received from Juliet H.:
“Released in 1979, the Clipper 42 was 12.8m x 3.7m with a draft of 900mm and, fully laden, displaced around 9 tonnes. Alibi was the prototype, built with a sandwich construction of strip-planked cedar, fiberglass on both sides. A mould was taken off the prototype so that all future boats could be full GRP with a balsa core. However, Crescendo was the only boat ever pulled from the mould.”
I would recommend that readers revisit ALIBI’S cameo appearance in part 2 of the series to see some wonderful images of her exquisite finishing and interior.
A final note re CRESCENDO. – She has been seen reasonably recently, in the South Island, I have been told, so any further help with information about her in any way, would be much appreciated.
LISTER MARINE DIESEL ENGINES
I had considered including LISTER MARINE DIESEL ENGINES in the group, however, there are quite a good number of these engines that are or have been in use in NZ., in many work boats, fishing boats, tugs, & a few pleasure craft, & in the end I decided they fell just outside the scope of what I was about, so will just make a general mention of them, with a few images of the odd pleasure craft, all of which had these engines installed by Roy L.
Roy Lidgard used quite a number of them in various types of craft, the 1940s & 1950s, mostly 4 cylinder, & also had a 4cyl version of the Lister Diesel driving the Smeltinghouse Bay Kawau island sawmill, he set up & ran on his property, in the later 1940s & 50s, the remains of which are still there today.
As just a brief mention, he installed Lister diesels, in the ROSE, (2 CYL) (later LA ROSA) Clive Power’s WAINUNU, (4 CYL) & TAWHIRI, a lovely sedan topper R Lidgard built in the mid/later 1940s (4 cyl)
THE ROSE (NOW LA ROSA)
TAWHIRI BUILT BY R LIDGARD 1940s WITH 4 CYL LISTER MARINE DIESEL AS ORIGINAL
WAINUNU WITH CLIVE POWER AT THE HELM, WITH HER 4 CYL LISTER DIESEL, WITH THE EXHAUST OUT THE TOP OF THE MAST. c1940s
Screenshot
ROY LIDGARD’S SAWMILL, SMELTINGHOUSE, BAY KAWAU ISLAND c. LATER1940s
LISTER 1940s 3 CYL MARINE DIESEL ENGNE AS AN EXAMPLE OF THAT ERA
EPILOG:
Well, readers, we have come to the end of this seven-part journey, and I can only say that for me, it has been a wonderful ride, to share with all of you who have taken the time to share the ride with me, and to follow the seven parts of what I’ve learned throughout my lifetime.
So often, you know as much, if not more, than I do. While some may have learned a little from me, I have, in turn, learned much from many of you, as we have shared this journey together, & I thank you all, for the opportunity to gain this new knowledge from you.
I especially want to express my humility and gratitude, for the kind words of thanks and appreciation, in some of your comments directed towards me personally.
I have done this most of all, to encourage us all, to share and record publicly, what we know about our New Zealand-based boats, with each other, and most importantly, to provide a public record, for the benefit of the boaties of the future. Those who will come after we old wrinklies have all gone, & will become the stewards of tomorrow. As a result of what we all write now, they will hopefully have the chance to understand what has gone before in all or many aspects of what will become their boats, the majority of which will surely live on long after we are not here.
AN INSIGHT INTO NZ’S UNIQUE MARINE ENGINES – Part Six Todays WW story follows on from earlier stories – link below to Part One, Two, Three, Four and Five As per pervious stories in the series the content has been pulled together by Ken Ricketts and ‘polished’ byPatrica and Ken’s daughter Corinne Pettersen. As always we have endeavoured to be as factual as possible but there will always by matters others will either know more about or be able to correct errors – so woodys do not hold back in commenting.
BENZ DIESEL ENGINE – BENZ OM59 55HP 4CYL DIESEL ENGINE PROBABLY SIMILAR TO THAT IN THE MANUNUI
MANUNUI WITH HER 55HP 6 CYL BENZ DIESEL ENGINE DURING WWII
MANUNUI AS BUILT AT SPEED WITH HER BENZ DIESEL ENGINE
The MANUNUI was built for Percy Colebrook in 1939 by Bill Couldrey and had a medium / slow revving 6 cylinder 55 hp Benz Diesel engine fitted when built, which she retained until 1963 when it was replaced by a 100 hp Perkins Diesel.
CRUSADER V8 MARINE PETROL ENGINES
TWIN CRUSADER ORIGINAL V8 PETROL ENGINES HAVING SERVICING, FROM THE RIVA TRITONE “LOLA,” WHICH ARE STILL IN HER TODAY.
Crusader engines, while major marine engine suppliers in America and other countries, have only made a cameo appearance in New Zealand, with only a handful of these lovely engines in use here, as far as I can ascertain.
Overview: The only craft I personally know of for certain is the stunning 1962 Italian-built Riva Tritone, LOLA.
However, WINSOME II may have had one, back around the 1950s when owned by Andy Donovan. I know her previous Chrysler 8-cylinder inline engine was replaced around that time by a V8, that was either a Crusader, Chris-Craft, or Flagship. However, the memory banks have failed me, making it impossible to determine which of the three it is, so come on, you WINSOME II experts, help me out here!
In the 1960s, Crusader Marine Engines was a prominent brand worldwide, providing inboard power for many boats, particularly cruisers and sport fishermen. They were known for their premium quality and reliability, used by leading boat manufacturers like Chris-Craft.
Crusader engines were based on standard automotive engines, but were marinized for marine use, with many of them based on Ford engines, and later with Hercules and Chrysler base units.
LOLA WITH HER 2 X CRUSADER 270HP PETROL ENGINES
LOLA, the 1962 Italian-built Riva Tritone Aperto, has a LOA of 27 ft and is one of only 15 in the world.
It is believed to be the only original Riva in New Zealand and a stunning example of boat restoration, all completed in NZ. Only 3,000 Rivas were built between 1950 and 1966, and she still has her original engines. She lives, or did live, in her own, purpose built, fully air conditioned boat shed, on the banks of the Marlborough Sounds.
WINSOME II – MAY HAVE HAD A CRUSADER V8 PETROL ENGINE IN THE 1950s /60s ERA – POSSIBLE ALTERNATIVES ARE FLAGSHIP & CHRIS CRAFT
CHRIS CRAFT PETROL ENGINES.
CHRIS CRAFT 1950s 6 CYL FLATHEAD PETROL 135hp ENGINE SIMILAR TO THAT IN THE GLENIFFER IN THE 1950s
These are another brand of engine that is sold in huge numbers worldwide, particularly in America, where all genuine Chris-Craft boats are built. However, they have only made a cameo appearance in New Zealand, with most of them coming here in imported Chris-Craft boats.
There are a few New Zealand-built boats that have or have had them. I have only ever seen a petrol version, although naturally, they do produce diesel engines in their lineup. All the engines they produce are based on other major engine manufacturers’ base engine blocks and are marinized by them. Hercules is a major engine block supplier to them.
GLENIFFER WITH HER CHRISCRAFT 6 CYL FLAT HEAD PETROL ENGINE RUNNING ON KEROSENE IN THE 1950s – OWNER PERCY JENNINGS IS AT THE HELM.
Input copied from previous post, ex Harold Kidd. – “Trevor Davis sold GLENIFER to P J Jennings of Paeroa in 1937 and he sold her to George Manktelow of Paeroa in about 1959. The Gleniffer was replaced by a 6-cyl Chris Craft (Hercules block) during the 50s, converted to run on power kerosene with a Model A Ford Zenith carb.”
FLAGSHIP MARINE ENGINES
FLAGSHIP 1958 250HP V8 PETROL MARINE ENGINE – BASED ON A CHEV BLOCK
There were a number of these engines that found their way to NZ in the 1950s/60s era and this is one of the possibilities for the V8 engine that was installed in the WINSOME II in that era by Andy Donovan who may also have had an agency for them, around that time.
AN INSIGHT INTO NZ’S UNIQUE MARINE ENGINES – Part Five Todays WW story follows on from earlier stories – link below to Part One, Two, Three and Four As per pervious stories in the series the content has been pulled together by Ken Ricketts and ‘polished’ by Patrica and Ken’s daughter Corinne Pettersen. As always we have endeavoured to be as factual as possible but there will always by matters others will either know more about or be able to correct errors – so woodys do not hold back in commenting.
LINDA, AT CHRISTMAS 1948, TAKEN IN SCHOOLHOUSE BAY, KAWAU ISLAND, JUST AFTER HER LOEW-KNIGHT PETROL ENGINE HAD BEEN REPLACED, WITH HER GM DETROIT 165HP MARINE DIESEL.
COQUETTE, POST HER LOEW KNIGHT-ERA
I know of only two boats that have these very rare versions of the Knight sleeve valve engine. One is the 1928 Colin Wild-built LINDA, which was bought by Roy Swales just after WWII with her original Loew-Knight 6-cylinder petrol engine. I saw it running, and it was incredibly smooth, quiet, and looked very tiny in LINDA’s huge engine room. It was painted silver and had the name “Loew-Knight” in a scroll, cast into the inspection plates on the crankcase.
Roy W. replaced it in 1947 with a 6/71 GM Detroit 165 HP diesel engine.
The other boat was the delightful Logan-designed and built COQUETTE, with her sedan top, which was added many years later by Arnold Couldry. He kept her delightful lines perfectly with this addition. She had a 4-cylinder version of the Loew-Knight sleeve valve engine, also painted silver. I tend to think this may have been her second engine because of her age, having been built in the early 1990s.
FODEN 2 CYCLE DIESEL ENGINES.
FODEN 12 CYLINDER 2 STROKE, MARINE DIESEL 256HP ENGINE – 2 X 6 CYL ENGINES SIDE BY SIDE ON ONE CRANKCASE IN 1 ENGINE
FODEN 6 CYL 2 STROKE DIESEL ENGINE
FODEN 6 CYL 163HP, MARINE DIESEL ENGINE
ORIGINAL FODEN ENGINES IN THE HDML MANGA, AS SOLD BY THE NAVY
KUPARU NOW OWNED BY SCOTT PARRY BELIEVED TO STILL HAVE 2 FODEN DIESELS
HMNZS KUPARU
HMNZS MANGA
DEODAR IN PRIVATE OWNERSHIP AFTER HER DAYS AS THE POLICE LAUNCH
LADY MARGARET WITH HER 2 X 6 CYL FODEN DIESELS – (Built by Dick Lang)
MARNINE WITH HER 2 X 6 CYL 163HP FODEN MARINE DIESELS IN MARCH 1963
WHITE CLOUD LAUNCHING DAY WITH HER 4 CYL., HOME MARINISED FODEN DIESEL
There are only three pleasure launches that I know of that have these engines, and there are two with 6-cylinder versions. The LADY MARGARET (built by DICK LANG) replaced her original two Fairbanks Morse Diesels; the MARNINE, which had two of them from when she was built, had the same specifications and was installed at the same time as the LADY MARGARET. The third boat was the WHITE CLOUD, which had a 4-cylinder home-marinized version, fitted by or for, the managing director of Fodenway Motors, Penrose. They were the New Zealand agents for Foden engines at that time and had her built and baselined a generator set to convert the 4-cylinder Foden for marine use in his new boat. This installation took place at their Gt. South Rd premises after being built at 1A Summer St, Ponsonby, by McGeady (Supreme Craft).
In addition to these boats, all RNZN-owned HDMLs and the first of the Police Launches named DEODAR, (DEODAR I), had two of them installed. All were originally 6-cylinder versions; however, but with the HDMLs., some engines were later replaced with 12-cylinder versions in some boats, which were, in effect, two 6-cylinder engines side by side in one crankcase. These had one drive shaft and two crankshafts connected by a system of gearing. At least one twin x 6-cylinder installation is believed to still be in a boat & still surviving today. It is in the massively refurbished, now privately owned KUPARU, primarily located in Whangarei.
Foden engine manufacturing and parts supply were sold to Rolls Royce in the late 1970s, and production ceased when they took over the Foden manufacturing rights.
waitematawoodys.com #1 for classic wooden boat stories, info, advice & news - updated daily - 14+ million views 