CLASSIC LAUNCH MOOSE -A Sneak Peek

CLASSIC LAUNCH MOOSE -A Sneak Peek

Back in April 2023 we ran a story on the 28’ launch – MOOSE, built / launched in early 1939 by Collings & Bell, link below to that story. At the time boat builder Alan Craig (Craig Marine) provided and update us on the vessel, including photos.
WW APRIL 2023https://waitematawoodys.com/2023/04/27/moose/

Fast forward to Tuesday night and I get an email from Craig headed up ’Sneak Peek’ – now Alan’s emails are few and far between but always include gold, so I was keen to open and view.The sneak peek was the above two photos of MOOSE being extracted from her boat house at Moose Lodge, on the shore of Lake Rotoiti.

Alan has promised more photos / detail asap, so fingers crossed.
We will follow this project closely, the launch has wonderful provenance and will be in great woody hands at Craig Marine.

AN INSIGHT INTO NZ’S UNIQUE MARINE ENGINES – Part Five

AN INSIGHT INTO NZ’S UNIQUE MARINE ENGINES – Part Five
Todays WW story follows on from earlier stories – link below to Part One, Two, Three and Four 
As per pervious stories in the series the content has been pulled together by Ken Ricketts and ‘polished’ by Patrica and Ken’s daughter Corinne Pettersen. As always we have endeavoured to be as factual as possible but there will always by matters others will either know more about or be able to correct errors – so woodys do not hold back in commenting.

PART ONE – https://waitematawoodys.com/2025/04/04/an-insight-into-nzs-unique-marine-engines-part-one/

PART TWO – https://waitematawoodys.com/2025/04/12/an-insight-into-nzs-unique-marine-engines-part-two/

PART THREE – https://waitematawoodys.com/2025/04/18/an-insight-into-nzs-unique-marine-engines-part-three/

PART FOUR – https://waitematawoodys.com/2025/04/26/an-insight-into-nzs-unique-marine-engines-part-four/

LINDA, AT CHRISTMAS 1948, TAKEN IN SCHOOLHOUSE BAY, KAWAU ISLAND, JUST AFTER HER LOEW-KNIGHT PETROL ENGINE HAD BEEN REPLACED, WITH HER GM DETROIT 165HP MARINE DIESEL.

COQUETTE, POST HER LOEW KNIGHT-ERA

I know of only two boats that have these very rare versions of the Knight sleeve valve engine. One is the 1928 Colin Wild-built LINDA, which was bought by Roy Swales just after WWII with her original Loew-Knight 6-cylinder petrol engine. I saw it running, and it was incredibly smooth, quiet, and looked very tiny in LINDA’s huge engine room. It was painted silver and had the name “Loew-Knight” in a scroll, cast into the inspection plates on the crankcase. 

Roy W. replaced it in 1947 with a 6/71 GM Detroit 165 HP diesel engine. 

The other boat was the delightful Logan-designed and built COQUETTE, with her sedan top, which was added many years later by Arnold Couldry. He kept her delightful lines perfectly with this addition. She had a 4-cylinder version of the Loew-Knight sleeve valve engine, also painted silver.  I tend to think this may have been her second engine because of her age, having been built in the early 1990s.

FODEN 2 CYCLE DIESEL ENGINES.

FODEN 12 CYLINDER 2 STROKE, MARINE DIESEL 256HP ENGINE – 2 X 6 CYL ENGINES SIDE BY SIDE ON ONE CRANKCASE IN 1 ENGINE  

FODEN 6 CYL 2 STROKE DIESEL ENGINE

FODEN 6 CYL 163HP, MARINE DIESEL ENGINE

ORIGINAL FODEN ENGINES IN THE HDML MANGA, AS SOLD BY THE NAVY

KUPARU NOW OWNED BY SCOTT PARRY BELIEVED TO STILL HAVE 2 FODEN DIESELS

 HMNZS KUPARU 

HMNZS MANGA

DEODAR IN PRIVATE OWNERSHIP AFTER HER DAYS AS THE POLICE LAUNCH

LADY MARGARET WITH HER 2 X 6 CYL FODEN DIESELS – (Built by Dick Lang)

MARNINE WITH HER 2 X 6 CYL 163HP FODEN MARINE DIESELS IN MARCH 1963

WHITE CLOUD LAUNCHING DAY WITH HER 4 CYL., HOME MARINISED FODEN DIESEL

There are only three pleasure launches that I know of that have these engines, and there are two with 6-cylinder versions. The LADY MARGARET (built by DICK LANG) replaced her original two Fairbanks Morse Diesels; the MARNINE, which had two of them from when she was built, had the same specifications and was installed at the same time as the LADY MARGARET. The third boat was the WHITE CLOUD, which had a 4-cylinder home-marinized version, fitted by or for, the managing director of Fodenway Motors, Penrose. They were the New Zealand agents for Foden engines at that time and had her built and baselined a generator set to convert the 4-cylinder Foden for marine use in his new boat. This installation took place at their Gt. South Rd premises after being built at 1A Summer St, Ponsonby, by McGeady (Supreme Craft).

In addition to these boats, all RNZN-owned HDMLs and the first of the Police Launches named DEODAR, (DEODAR I), had two of them installed. All were originally 6-cylinder versions; however, but with the HDMLs., some engines were later replaced with 12-cylinder versions in some boats, which were, in effect, two 6-cylinder engines side by side in one crankcase. These had one drive shaft and two crankshafts connected by a system of gearing. At least one twin x 6-cylinder installation is believed to still be in a boat & still surviving today. It is in the massively refurbished, now privately owned KUPARU, primarily located in Whangarei.

Foden engine manufacturing and parts supply were sold to Rolls Royce in the late 1970s, and production ceased when they took over the Foden manufacturing rights.

MILFORD MARINA MOOCHING

MILFORD MARINA MOOCHING

Given all the recent upgrades in the marina it seems wrong to refer to it as Milford Creek. Maybe the areas now fitting of the name that some of the mud berth dwellers use – ‘Wairau Cove’.

I spent some time there yesterday helping with the relaunch of Angus Rogers 1968 Bailey & Son built launch – CENTAURUS that had been out at the Slipway Milford railway slip for some TLC and a JPPJ (Jason Prew Paint Job) – a minor opps – flat batteries………. meant a delayed start, so plenty of time to pull the camera (phone) out. A 3.5m tide equalled a lot of activity at the Slipway and the adjacent Milford Cruising Club hard stand.

The standard of the woodys in the marina seems to be improving in the last few years , probably a combination of the new bridge , upgraded MCC yard and the big crew working at the Slipway Milford. 

Nice to see that the small berths along the roadside have almost exclusively been taken over by the Pied Piper fleet. The MCC yard was home to some out for early winter TLC.

I won’t disclose how many berthing attempts we had back at CENTAURUS’s marina but while Angus blamed the out going tide and wind – me thinks the new JPPJ was the reason i.e. skipper was a tad gun shy and didn’t want to mark the boat on the first outing 😉

AN INSIGHT INTO NZ’S UNIQUE MARINE ENGINES – Part Three

AN INSIGHT INTO NZ’S UNIQUE MARINE ENGINES – Part Three

Todays WW story follows on from earlier stories – link below to Part One and Two 
As per pervious stories in the series the content has been pulled together by Ken Ricketts and ‘polished’ byPatrica and Ken’s daughter Corinne Pettersen. As always we have endeavoured to be as factual as possible but there will always by matters others will either know more about or be able to correct errors – so woodys do not hold back on commenting.

PART ONE – https://waitematawoodys.com/2025/04/04/an-insight-into-nzs-unique-marine-engines-part-one/

PART TWO https://waitematawoodys.com/2025/04/12/an-insight-into-nzs-unique-marine-engines-part-two/

ROLLS ROYCE MARINE DIESEL ENGINES

ROLLS ROYCE 275 HP MARINE DIESEL ENGINE

ONE OF THE 2 ROLLS ROYCES THE ORIGINAL ENGINES IN OHORERE

KUDU WITH HER 137 HP ROLLS ROYCE ENGINES IN 1966

OHORERE WHEN NEW, WITH HER 2 X ROLLS ROYCE 6CYL. 275 HP DIESEL ENGINES

OHORERE AS AT 2025 WITH HER 2 X 770 HP MTU MARINISED MERCEDES BENZ DIESELS

MANAIA, WITH HER 2 X 6 CYL. 275 HP ROLLS ROYCE ENGINES

MANAIA INSTRUMENT PANEL

These are, as one would expect, a brand of engine that is quite rare, resulting from the cost of the engines to buy and the cost, equally, of parts for all maintenance. Also, while Rolls Royce has the name synonymous with perfection in all respects, it is my view that, in fact, Gardner engines are far superior in every respect, including noise, smooth running, longevity, maintenance necessity, and costs thereof. However, there are a few that are in the boats of today and yesterday. I personally know only three.

There is the KUDU, a large launch that, at one time, in mid to late 1966 to perhaps somewhere around the 1980s, belonged to the late Harry Julian. She is 63 feet long and powered by 2 x 137hp Rolls Royce 6-cylinder diesel engines. She was designed and built under Lloyd’s supervision in the UK in 1964 and sailed out to NZ as the end of a 20,000 km journey. However, the last time I saw her was on a visit to the Gold Coast in Australia, anchored in the middle of the center of Sanctuary Cove Marina.

Another of the RR-powered boats is the OHORERE, built by Percy Vos in Auckland for the government of the day to be a high-speed fisheries patrol craft, and designed by Thornycroft in the UK. However, she never reached anything close to her anticipated speed projections as required in the order from the government to the designers and builders. Large sums of money were spent collectively by the designers, Rolls Royce, and the builders to give her better performance, but they failed miserably, and she was ultimately sold to private ownership, where she has been used for many years now for fishing charters in Tauranga. As of now, Rolls Royce’s were replaced about two years ago with 2 x 770hp MTU marinized Mercedes Benz diesels and is capable of around 30 knots.

There is one more pleasure craft, an ex-Whangarei pilot boat and that is the MANAIA, which has had from new, 2 x Rolls Royce 8-cylinder inline 16-litre diesels. 

UNIVERSAL BLUE JACKET 6 FLAT HEAD PETROL ENGINES.

THE UNIVERSAL RANGE OF 4 & 6 CYL BLUE JACKET RANGE OF MARINE ENGINES

OTAZEL WITH HER UNIVERSAL BLUE JACKET 6 PETROL MARINE ENGINE. MANSION HOUSE BAY, KAWAU ISLAND c.1951

I am aware of one of these in New Zealand, which was in the OTAZEL, owned by Arch Tucket, in the late 1940s to the 1960s. He was the head of the patrol craft section for T.E.A.L. at that time in Mechanics Bay, and he fitted it to her on the hardstand at Okahu Bay in the winter of 1950.

G.M. ALLISON 1450HP, HOME MARINE CONVERTED, V12 AIRCRAFT PETROL ENGINE.

GM ALLISON V12 AIRCAFT ENGINE

REDHEAD, IN THE SOUTHWARD TRUST VEHICLE  MUSEUM IN PARAPARAUMU, AS SHE WAS LIFTED FROM THE SEABED IN WELLINGTON HARBOUR, AFTER HER  PROPELLER LOSING A BLADE, WHILST RACING & SINKING AS A RESULT.  

REDHEAD RACING A FLYNG BOAT ON WELLINGTON HARBOUR

The only boat I’m aware of that had one of these was Sir Len Southard’s champion racing boat, REDHEAD, which won, at one time or another, most of the cups and awards, as well as a huge number of races in her time. She was a real champion, designed, built, and raced by the late Sir Len Southward of Wellington, a brilliant engineer and philanthropist. John Bullivant tells has advised there was a second high-speed hydroplane racing boat built with a marine-converted V12 GM Allison petrol engine in the same era.

STERLING MARINE PETROL ENGINES

STERLING 6 CYL 1920 MARINE PETROL ENGINE PROBABLY SIMILAR TO THAT 

IN LADY STIRLING

STERLING 115 HP U.S. NAVY WWII FLAT HAD PETROL ENGINE

KERMATH 1928  225 HP SEA WOLF ENGINE IDENTICAL TO THAT IN THE TASMAN IN 1947

LADY STERLING IN QUEESNTOWN

TASMAN IN 1948 IN SCHOOLHOUSE BAY KAWAU ISLAND  

STERLING BUILT IN 1926 BY ERNIE LANE IN PICTON

LADY STERLING

The 52-foot, 105-year-old Bailey & Lowe-built ocean-going yacht, built in 1920 is named LADY STERLING. This yacht had one of these engines originally, and there were other boats that had them in the earlyish 1900s. 

LADY STERLING has, in recent times, been in the Queenstown area, but she has traveled many thousands of sea miles, with numerous crossings of the Pacific Ocean in her long life. 

Around the end of WWII, she belonged to Stan Waters. She passed shortly after to Lloyd McIvor, a dentist, who sailed her several times a year to Fiji and other Pacific islands to attend to the islanders’ dental issues.

TASMAN WITH A STERLING 6CYL DUAL IGNITION 115HP WWII U.S. NAVY PETROL ENGINE.

A reference in part 1 of this series was made in the comments section by Denis O’Callahan, related to the TASMAN having had a WWII ex-US Navy 6-cylinder flathead Sterling petrol engine at some stage, pre-1975. I have researched this engine and found the following information and images related to it, which I am confident may well be the engine he was referring to.

A quote from Tom Ball in 2016: “I have acquired this engine recently. It is a six-cylinder marine engine with dual ignition. It is 115 HP with a water-cooled exhaust. These Sterling petrol engines were made in Buffalo, New York. The engine supposedly was in a naval ship of some sort and may have come from the naval yard there.” – unquote

As I also said in part 1, I was aboard TASMAN, Christmas 1947 with my father one day & owner, Jack Brooke, lifted the bridgedeck floor & showed us her huge bottle green 225 hp overhead valve Kermath Sea Wolf  petrol engine, identical to that in the above image.

I could see by its size & overall concept, it was a fairly old engine, & perhaps the original, & in the circumstances, I have taken what to me, is a logical view, that this engine was probably replaced around 1960ish by the Sterling, due to old age , &/or perhaps maintenance issues, as well as huge quantities of petrol it must have consumed. Also, it was usually pushed at high speed most of the time by Jack B who was a speed fiend, when it came to his boat, which must have given the engine a hard life.  

19-04-2025 INPUT ex RUSSELL WARD“I have a little input into Tasman when she had the Stirling engine in the early -mid ’60s. We used to describe it as a “Sterling Dolphin” in the day. My mother had a business connection with her then owner Dr Jim Sprott and I had the chance to see over Tasman and especially to view her engine. It was a four cylinder T head type engine -two blocks of two and quite tall. Certainly painted green with lots of brass -It ran delightfully smoothly and the owner averred that it was not too thirsty if throttled back. His suggestion was that the Americans installed the engine during the war to get more speed out of her. It certainly was a very old vintage- looking engine and had none of the looks of the more modern engines.

Dr Sprott later decided to replace it because of the petrol it used and maintenance. It was offered to MoTat who refused and my father wouldn’t allow me to have it and the word was that it was scrapped. RIP.”

26-04-2025 INPUT ex DENIS O’CALLAHAN – below further information regarding the Sterling engine in the launch – TASMAN

In 1970, TASMAN was purchased from Dr.Jim Sprott by my friend Allan Tyler and his dad Eric.

She had a Sterling 6 cylinder petrol engine with dual ignition and we were told that the original engine may have been a Kermath.

We had many adventures with this engine. One time at Tryphena she would not start and we found the Bendix Spring was broken. To our relief we found several spare springs in the locker so it must have happened before.

The Sterling was replaced in 1976 with a Lees Marine 6 cylinder Ford diesel. New stainless steel fuel tanks amidships replaced the old copper tanks under the aft deck which became the water tanks. The old Sterling engine went to scrap but we retained the name plates which were passed on to the new owner of TASMAN, Stephen Cashmore.

Photographs of these plates are below and the following is my interpretation:

Silver badge “Sterling”. THE ENGINE OF REFINEMENT FOR THE FINEST BOATS THAT FLOAT.

Small Plate. US NAVY. BU. ENG. NO. (Bureau of Engines Number) –  11725

Large Plate. STERLING ENGINE CO.

                        BUFFALO NY USA

            BUILDERS OF MARINE ENGINES

                       SERIAL NUMBER

                            US L61678

           ROTATION AT FLYWHEEL C.C. (Counter clockwise)

         C.W. HAND SCREW PROPELLER

                 HORSE POWER 220

                RPM MAXIMUM 2200

        WITH PROPELLER LOAD AND

            FULL OPEN THROTTLE

     ENGINE REVOLUTIONS MUST

     EQUAL OR EXCEED 1900 RPM

               FIRING ORDER

                 1 4 2 6 3 5

          TAPPET CLEARANCE

           INLET 020 THOUSANDTHS

    EXHAUST 025 THOUSANDTHS

In 2019 I visited Buffalo New York on a cruise through the Erie Canal and Great Lakes and looked for the old Sterling works.

I found that Sterling had been taken over by Phillips Petroleum in the late 1950s and the assets moved to Kansas.

The Sterling Company dates back to about 1903 and many speed records were held by boats with Sterling engines.

STERLING TEE HEAD 4 CYL PETROL MARINE ENGINE SIMILAR TO THAT AS DESCRIBED BY RUSSELL WARD ABOVE THAT HE COMMENTS WAS INSTALLED IN TASMAN IN THE 1960’S AFTER HER ORIGINAL KERMATH SEAWOLF

THE LAUNCH STERLING

I have researched extensively but have been unable to source an image of the 3-cylinder, 27 HP Sterling engine, as referred to below by Harold Kidd and in the launch STERLING as pictured above.  

Input from Harold Kidd: This STERLING was built by Ernie Lane in Picton in 1925 for L.J. Steele as a passenger vessel to carry 60 passengers and had a 1924-built, 3-cylinder, 27 HP (rated) Sterling marine engine with a bore of 4.5″ and a stroke of 5.5″. Dimensions are 34′ x 9′ x 3’9″.

HALL SCOTT DEFENDER V12 PETROL 630HP MARINE ENGINES

NGAROMA WITH HER 1 HALL SCOTT DEFENDER V12 PETROL ENGINE, & 1 GLENIFFER 8 CYL INLINE DIESEL ENGINE, WHEN OWNED BY JIM LAWLER

These Hall Scott Defender petrol engines were used in all Fairmiles during WWII wartime service. When sold into private ownership after the war, all were immediately replaced by diesel engines of various types, brands, and sizes, except for one privately owned Fairmile called the NGAROMA, owned at that time by Jim Lawler. This vessel retained one Hall Scott engine for around two years before replacing it with a second, opposite-handed, 8-cylinder inline Gleniffer Diesel to match the existing Gleniffer 8-cylinder engine he fitted when he purchased the NGAROMA, creating a matched handed pair.

There were also two RNZAF MIAMI CLASS American patrol craft bought by the RNZAF around 1948. One, W275, was sent to Lauthala Bay, Fiji, by the RNZAF, while the other, W276, remained here. W276 had two Hall Scott Defenders mounted in the stern and vee driven.

W276 WITH HER 2 HALL SCOTT DEFENDER V12 PETROL MARINE ENGINES  

JUNKERS GERMAN DIESEL AIRCRAFT ENGINE TO BE HOME CONVERTED FOR MARINE USE 

JUNKERS DOUBLE ACTING DUAL PISTON 6 CYL estimated at c.1000HP GERMAN AIRCRAFT ENGINE.

This boat (W276) as featured above, was sold in the 1960s to a Mr. Canavan, a retired senior Air Force officer. He employed two marine engineers to convert two German two-stroke Junkers aircraft diesel engines (probably the same or like those in the image above), which, as far as I can interpret, seem to have been around 1,000 hp each. He acquired and converted them for marine use, replacing the two Hall Scotts with these engines. 

This was a long and very expensive task for Mr. Canavan. During this process, she was moored adjacent to the up-harbour end of the Naval Base and was still painted air force grey. During the installation she acquired four very large exhaust pipe holes near the deck line at the stern.

These engines, like the engine in the hydrofoil MANU-WAI, required hot engine oil to be pumped through them for 20 minutes before cold starts. The two engineers, as mentioned above, eventually finished the project and went off to find Mr. Canavan so he could be present for their first start. While they were away looking for him, he turned up, went out to the boat, saw that they were ready to go, and pushed the buttons. They started but immediately seized up as they had not had the hot oil process completed first.

When the two engineers came back, they were naturally furious that after all their hard work, it had all come to this. So, as one would expect, they just picked up their tools and walked off the job. Eventually, Canavan got two more engineers to rebuild the engines, and while they were in the process of this, one day, when they were brazing with bottled gas, the stern end of the boat caught fire, and the aft 20 feet or thereabouts was destroyed. 

The insurance company sold her “as is, where is,” and someone bought her, chopped off the burnt-out back end, and fitted her, in her now shortened form, with two 6/71 GM Detroit diesels, added new pleasure craft-type coamings, and called her the LADY SOMETHING? or SOMETHING LADY?. This work was all done on the hardstand at Half Moon Bay Marina.

With her back end chopped off and her new coamings fitted, she looked very short and fat.

WAUKESHA HESSELMAN, LOW COMPRESSION, SPARK IGNITED DIESEL ENGINES.

WAUKESHA HESSLEMAN, SPARK IGNITED, 6 CYL DIESEL ENGINE.

WAUKESHA HESSELMAN SPARK IGNITED  LOW COMPRESSION DIAGRAMATIC VEW OF ENGINE DESIGN.

AWARUA WITH HER 6CYL WAUKESHA HESSELMAN DIESEL ENGINE.

LADY RAE, STANDING IN, FOR IDENTICAL SISTERSHIP, GALA LASS.

There were only two boats fitted with the 6-cylinder version of these engines, which had around 100+ hp. 

They were Ted Cooper’s built and owned AWARUA, which for the first couple of years had a Redwing petrol engine. He later replaced this with a Waukesha Hesselman 6-cylinder diesel, which she had for the remainder of his stewardship. A later owner, replaced it with a Ford diesel.

The other boat was the GALA LASS, which had an identical sister ship, the LADY RAE. 

GALA LASS had a Waukesha Hesselman diesel from new for the entire time of ownership by the original owner, Tony Hurt.  The LADY RAE had both one and two engines at different times, both with petrol or diesel, as was appropriate during her early years. I have not been able to locate an image of GALA LASS. I have substituted an image of LADY RAE in place of GALA LASS. 

STELLA – CLASSIC WOODEN BOAT SOS

20+ years ago

STELLA – CLASSIC WOODEN BOAT SOS

Last week Andrew Motte-Harrison commented on one of the stories that he had a old kauri launch ’currently deteriorating behind his farm hay shed’.

Andrew believes she was originally named STELLA and alsp possibly named TOILER at another time. Possibly built c.1910>15 by Lane Bros in Christchurch (thats a new one, was there such a place?). Andrew described STELLA as a line fishing boat.

Andrew also commented that when they had her up at the Nelson Marina, talking to an elderly boat builder up there years ago, he passed on what he understood to be some of her history.  He thought she had been working out of Bluff, Hokitika and perhaps Oban in years past (back then)

As the photos show the boat is in need of some serious TLC, starting with a few hours with a water blaster- inside and out. And maybe a session with a tungsten tipped chainsaw and then a new cabin. Her hull deserves saving.

The last photo was taken  over 20 years ago, before being hauled out.

So southern woodys anyone looking for a project, STELLA is located 20 minutes south of Murchison, approx. 2 hours out of Nelson.

INPUT ex DICK HALL – Built by Ernie lane in Picton for the Boese family with a low cabin and rails instead of bulwarks. Later purchased by well known fishing identity Jimmy Aldridge and converted by Jack Morgan with new wheelhouse, bulwarks and new air-cooled Lister. Jim crayfished mostly outside Tory Channel. Next owner Alex McKenzie from Blenheim who re-named her Toiler but after a few years sold her for a bigger vessel. Fished out of Picton all her life before going to Nelson for pleasure conversion. Her original name was Elaine then Toiler. Never Stella while in Picton

WHAT HAPPENED TO THE CLASSIC WOODEN YACHT – NAOMA

c.1961

WHAT HAPPENED TO THE CLASSIC WOODEN YACHT – NAOMA

As covered off in Fridays WW story, Mike Prigg is looking to learn what became of his father , John Prigg, old classic craft. John owned two woody’s in the 1960’s. We featured the launch – TINA MARIA on Friday and were successfully able to ID her as the launch – OCEAN QUEEN.

Today its the turn of his yacht named NAOMA, that was sold in about 1961. NAOMA was kept in Westhaven during John’s ownership.

The name NAOMA does not appear in WW search records, so both Mike and WW are keen to uncover more on her.

Link here to the Friday TINA MARIA > OCEAN QUEEN story 

15-04-2025 INPUT ex Jason Prew – Jason reports in that the above yacht is most likely under wraps at the Milford Boating Club yard – see below.

HELP NEEDED TRACKING DOWN THE WOODEN LAUNCH – TINA MARIA

TINA MARIA – c.1965

HELP NEEDED TRACKING DOWN THE WOODEN LAUNCH – TINA MARIA

WW has been contacted by Rob Staub (MV SURPRISE) on behalf of his friend, Mike Prigg who is hoping to learn what became of his father , John Prigg, old classic craft. Mike and Rob attended the Australian Wooden Boat Festival in Hobart in February and the festival triggered memories for Mike of the two woody’s his father owned in the 1960’s. And of course Mike’s eager to hear if they are still afloat today.

The launch is named TINA MARIA and was sold in about 1965. There is also a yacht but we will cover her off in WW’s Sunday story

TINA MARIA was kept in Westhaven during John’s ownership. And Mike understands she was originally kept in the Te Atatu River.

WW along with Mike are keen to uncover more on TINA MARIA.

UPDATE ex Nathan Herbert – well that was quick – Nathan has already ID’ed TINA MARIA as the launch OCEAN QUEEN that has made numerous appearances on WW and these days resides on Lake Taupo. Photos below ex Paul Stewart, and link to one of her WW stories. Keen to learn when the name change occurred. We learnt in the WW story that she was probably built by Joe Slattery in 1920 and was named OCEAN QUEEN when launched, so at some stage she has had a name change to TINA MARIA and reverted back. https://waitematawoodys.com/2019/08/05/ocean-queen-a-peek-down-below/

2019
2014

CLASSIC WOODEN LAUNCHES – AWARIKI & CENTAURUS GETTING SOME TLC

AWARIKI

16-05-2025 YARD UPDATE – work continues on AWARIKI, interior looking very sharp + the new varnished coamings are a game changer – love it.

CENTAURUS

CLASSIC WOODEN LAUNCHES – AWARIKI & CENTAURUS GETTING SOME TLC

Dropped into the Slipway Milford yard yesterday and very happy to see two woodys hauled out on the railway slips for some serious TLC.

We reported in mid Feb (link below) that the 32’ 1967 Owen Woolley built and designed launch – AWARIKI was in the process of losing her flybridge (✔️), well woodys the work continues, the team are currently refurbishing the interior. 
https://waitematawoodys.com/2025/02/19/classic-wooden-launch-awariki-gets-a-top-chop/

Alongside AWARIKI is the 42’ 1969 Bailey & Sons built launch – CENTAURUS, out for a JPPJ (Jason Prew paint job) that has turned into a back to bare wood effort. The starboard side has one coat on and already looks the bees knees. Owner Angus Rogers is onsite attacking the brightwork, so this old lady will be very regal when she relaunches.

Well done to both owners for investing in the upkeep of two of our finest classic wooden craft.

Bumped into a fried who is an antiques dealer and he showed me a recent find – the wording on the front of the gold medal / badge reads – Memorial Hewson Cup 1925, back – 14’ One Design Championship of Waitemata For Youths Under 21 – ‘Queen March’ – W. Rogers’. I bet W. Rogers had no idea the value of their medal in 2025.

INPUT ex ROBIN ELLIOTT – Queen March, sailed by Billy Rogers on that day, was owned by Eliot Davis, brother of Sir Ernest Davis, and named after Eliot Davis’ champion racehorse. The race was won on a resail because it was later revealed that the skipper of Joan, winner of the first race, was 2 days over the 21 years limit. Three medals were presented to each of the crew Billy Rogers, Doug Rogers and D. MacKay

GREAT BARRIER ISLAND WOODEN BOATS

GREAT BARRIER ISLAND WOODEN BOATS

The above photos were sent in by Glen Martin from a recent trip. The boat of main interest was STAR DRIFT that we have been keeping an eye on for several years – still no activity of note but the small fly-bridge has gone west at some stage – we like that.

Anyone able to put a name to the boat in the last photo.

CLASSIC WOODEN WORK BOAT – GEM

CLASSIC WOODEN WORK BOAT – GEM

Woody John Dawson sent in the top photo above and commented that he saw it on Phillip Carey’s – Carey Boats fb. All we know is she is named GEM.

In the second photo, from April 2020 WW story, we see GEM (#48) post launching. In the 2020 story we learnt from Richard Tosswill that GEM was built by Roger Carey pre. 1961. Sadlly in Dec 1962 she was lost at sea, later confirmed with the discovery of the wreckage.

GEM was 30′ in length and had wonderful lines and that stern …………

Can we learn more about her e.g. was she built as a workboat and if so what was her role.

30-03-2025 INPUT ex IAN MILLER – GEM was built in 1961 by Roger Carey, of Picton, for Fred Hall, a crayfisherman operating from Tatapouri, north of Gisborne. She replaced Fred’s previous boat, Clyde. Sadly, on 27th December 1962 GEM foundered at sea during a storm, extensive wreckage coming ashore north of Tatapouri, but Fred was never found.

More information can be found in the book, BY BOATS WE LIVE, a book about all the boats Roger Carey designed and built, or just designed. It was written and illustrated by Roger’s daughter, Joan Clark, an accomplished artist whose drawings and paintings illustrate each of the more than 40 featured in the book.