TEINA was built in 1922 by the McLeod Bros. In Bayswater, Auckland to a Glad Bailey design. Current engine is a 60hp Isuzu c240
Probably best described as a work in process / project boat, but as the architects say – its got good bones (see photo below), so at the asking price of $8k ono she has the makings of a good woody.
Kawau Island c.1930’s
OBC Marina OBC Marina
Currently waiting on a low tide to exit the OBC Marina – full report on Sundays OBC/Woodys event tomorrow – check out WW on Tuesday.
THE RESTORATION OF THE CLASSIC WOODEN EX WORKBOAT – ARIANA (TE KAWAU) – PART TWO
Following on from last Mondays story on Sven Wiig’s classic wooden vessel – ARIANA, previously named GLENROWAN and TE KAWAU. Sven has just sent in Part Two.
Todays story takes us up to last week and we will run Part Three on Wednesday and then woodys we will have to wait for the final part for a little while, but rest assured there will be one 😉
And as highlighted in Part One Sven is looking for any intel on her past , and is very grateful for those that commented last week.
“Once the decks were fibreglassed the next mission was to get the coamings and cabin tops rebuilt. Cabin tops were given two layers of ply and clashed in solid.
The little doghouse extension got the same treatment.
I had hoped to find bronze portholes for the coamings but couldn’t find any in the right sizes and quantity. I decided to copy the detailing that existed in the wheelhouse windows.
Next were the doors which I repaired and modified.
The wheelhouse sides were repaired with new tongue and groove.
Once all this had been sanded and given a couple of coats of paint the cover could be removed and I could finally stand back and check out my work. I was a bit nervous that I wouldn’t like my design choices once I could view them from a distance, but overall I was pretty happy with her.
Cover off after three years.
It had been more than three years now since she had come out of the water. Progress was frustratingly slow but with the cover now off it finally felt like I was getting there. Next up was to rebuild the Bulwarks. These had been cut away to gain access to the deck. I started cleaning off the old plywood getting ready to rebuild them. When I got around to the stern post I made a horrific discovery. I had always thought her stern wasn’t quite right I now discovered why. I dug out a large chunk of sikaflex and could see that her stem was cracked almost in two. All the screws holding her planks went straight into the crack. It appears that at some time in her past she suffered a trauma. Maybe she was crushed between another boat and a wharf, or hit from behind? Crikey what to do? All the others in the yard came and checked it out. There was lots of tut tuts and sucking through the teeth. A local boatbuilder suggested I cut the whole back off and put a transom on her. Humm… maybe not. It was not going to be an easy fix hence why it had never been fixed properly. Over the years more and more cotton had been jammed it there, more screws added then the sikaflex. This was why all the seams back there were large and the planks uneven, There was nothing for it in my mind I had to pull it all apart and repair it properly. I spent a good day just looking and trying to work out if I was biting off more than I could chew. Was there an easier way. Nope just had to go for it.
Dug out the putty and sikaflex to reveal the crack…
I cut off the outer stem which appeared to be a grown hardwood. Maybe pohutukawa? This revealed the full horror of the situation. Yep I was committed now.
I then carefully removed all the old screws from the planks, removed a knee on the inside and pulled the inner stem out. All that makes it sound easy. In reality it was several painful days where I questioned my life choices.
The inner stem removed from the boat. The crack when right though all the screws going into the cracked timber. To be continued in Part Three – on Wednesday.
THE RESTORATION OF THE CLASSIC WOODEN EX WORKBOAT – ARIANA (TE KAWAU) – PART ONE
Last week we ran a story from Sven Wiig on his wooden vessel – ARIANA, previously named GLENROWAN and TE KAWAU. Sven was looking for any intel on her past , as he undertook a rather epic restoration project. As I always do I asked for some regular updates and photos – well on Saturday the email inbox started to groan when Sven’s email arrived. Slightly different format today, but it suits the story – as told by the man himself.
THE NEW DECK
In May 2020 we bought ‘Ariana’. We knew she needed some work, there were obviously rotten bits here and there and the deck seemed a bit spongy in places but looking inside all seemed pretty sound and she had a brand new engine. How can we go wrong? The owner made me an offer I couldn’t refuse as he said he thought I was the right person to take her on and he wanted me to have her. So we bought her and had her transported down to Wellington and the same truck then took our old boat ‘Primadonna’ up to our good friends in Auckland.
Ariana arrives in Wellington
We enjoyed Ariana for a year just cruising the harbour and taking friends and family out for picnics. A year later I had a break in work and decided now is the time. Ariana was hauled out at Evans Bay I had six weeks before the next job and I was going to have the boat back in the water before I had to leave town. No problem pull the old ply up put some new ply down, easy. That didn’t go to plan. Pulling up the old ply revealed, compost. A bodged previous repair had been letting in fresh water for many years. I enlisted a friend to give me a hand and we kept digging. We discovered the entire deck structure, sheer clamp, carlins, cabin coamings and bulwarks were all rotten. At this point I made a panicked call to my brother Olaf who is a qualified boatbuilder and asked for advise. ‘No worries, you got this, one piece of timber at a time.’ My partner was less encouraging advising me that the only way forward involved a chainsaw and a skip bin. She was right. I seriously considered this option. Couldn’t do it, I had been entrusted with Ariana and I was going to save her. To encourage my madness Olaf came down from Auckland and gave me a hand to start laminating up the first section of sheer clamp. I continued demolishing pieces of the boat. In between I made new bits to try and keep spirts up. I pulled out the old fish hold, still under the rear deck, to discover ballast in the form of river stones and rusty railway iron. The pile of debris grew, less and less of Ariana remained.
My friend Bede discovering the extent of the rot.
Rotten wood and ballast.
Six weeks passed and I had to go back to work. I had some shear clamp and carlins in place and I had a destroyed boat. Several months passed while I was away working and I returned with new energy. Realising I was never going to get it done alone I convinced two clever friends to give me a hand. Pete, Marc and I started replacing deck structure, framed up and new front cabin and replaced planking where the rot extended into the top planks. Broken ribs were sistered with laminated white oak and riveted in place. We were making some good progress…
Front cabin framing underway.
Fiddly time consuming work.
New deck beams installed.
Then the budget ran out and work ground to a halt. Months passed with me only finding the odd weekend here and there to move the project forward. Slowly I finished the deck structure and created a small dog box extension to the wheelhouse, above the old fish hold. One day this will be a cabin for my son. A year had past and finally I could start laying some plywood for the new deck. A job I had optimistically thought I would be doing nine months earlier.
However before I could lay the ply at the stern I decided I had better investigate the lazarette hold. Something wasn’t right back there. I wasn’t to find the full extent of the un-rightness of this area for some time, more of that later. First was to chip out all the concrete that had been poured into the bilge. Several days of extremely unpleasant work later I had removed the concrete to reveal and section of keel or deadwood near the cutlass bearing that was all punky. Degraded by electrolysis. The anodes and bonding wires had taken a toll. I cut back the punky wood until I found good solid timber. Sealed it with epoxy and went looking for some more Kauri. Some large Kauri beams were sourced and a section of keel patched in with new floors.
Last of the concrete.
Keel patch coming together.
Moving on I built a hatch for the lazurette and laid the last of the plywood. Fibreglass was laid. She finally had a deck again and another year had passed. Two years into a six week project and I was maybe half way finished.
To Be Continued………
THE WINNER OF YESTERDAYS DES TOWNSON QUIZ RE NUMBER OF INDIVIDUAL DESIGNS – IS KEN MULGREW WITH THE ANSWER 74. As recorded in the Brian Peet book – Des Townson A Sailing Legacy.
CLASSIC DES TOWNSON 30’ YACHT – FALCON + Win a copy of the book – DES TOWNSON A Sailing Legacy
As most WW readers will know, Des Townson never designed an unattractive craft, that skill is harder to do as the size of the vessel decreases. I have often said on WW that very few people can get a >30’ craft looking ‘right’.
Mr Townson excelled himself with the design of the 30’ keeler – FALCON (Reg. #873), as seen above.
Falcon was built / launched in 1965 and constructed from double diagonal kauri, and no f/glass ✓.
Her owner Grant Wylie has been the custodian of FALCON for the last 17+ years and contacted WW to say that age and health were against him and could we help locate a new owner.
I asked Grant about headroom and I had to laugh at his reply – “Yes & No”, Des’s design eye always won out over comfort 🙂
FALCON is powered by a Bush 20hp engine and sports a KIWI prop. She is well kitted out for gulf cruising but needs a refresh, which is reflected in Grant’s price expectations.
A great opportunity to acquire for a modest price a classic yacht from the design board of one of New Zealand’s most paramount designers.
Continue to enjoy her as she is or put your sanding / painting skills to use this winter and prepare yourself for the compliments at anchor this coming summer.
AND AS AN ADDED BONUS TODAY – ANSWER THE QUESTION BELOW CORRECTLY AND YOU ARE IN THE DRAW TOWIN A COPY OFBrian Peet’s book – ‘DES TOWNSON A SAILING LEGACY’. A 343 page insight into the man and his designs.
Todays woody story has a twist to it – while the launch KOURA is a genuine classic wooden boat her days afloat are over. Not by neglect or mishap – read on to hear her story and hopefully one of you might be the next custodian.
At the time she had been transformed into a land based ‘man-cave’. Her new ownershad bought Koura to enable Chris Devereaux – a passionate boatie – to enjoy owning a vessel again despite being confined to a wheelchair. The family had many happy cocktail hours aboard her and their grand children had fun sleeping aboard and playing captains and pirates in the holidays. Restoring and creating the KOURA as she is today gave Chris a purpose and much joy.
Sadly Chris succumbed to his auto immune disease in late May and now partner Barbara Harris is selling their Whangarei property and KOURA needs a new home.
So woodys – if any of you are interested in buying her and continuing her story Barbara would love to chat. Whilst KOURA would be very cool as a ‘man cave’ , there must be a grandad out there with some spare land that he could install KOURA on. Me thinks that overnight you would become #1 grand parent.
If you or someone you know has room in their life for KOURA – initially contact Barbara at Bjaneharris1@gmail.com
Back in October 2019 woody IanMcDonald sent in some photos of the wooden launch – KOMUTU on the hard in Whagarei.We learnt that she was built by Curnow & Wilton in Motueka in 1950>52 (launched Dec 1952) to a Cliff Nalder design. Spec were 42’ x 12’ x 3’6”.
Fast forward to early 2025 and thanks to a tme appearance we get to have a gander down below. Forward motion these days is via 230hp Detroit 671 engine.
On Wednesday we asked for more information on the classic wooden launch – COLUMBIA and the WW readers delivered, link here to that story https://waitematawoodys.com/2025/06/25/looking-for-information-on-classic-launch-columbia/ .
Then on Thursday night Sandra Gibson sent in the gallery of photos above and advised that “Columbia has been restored by Stanford Boatbuilders, as she had been gutted. And she is now powered by a V8 Cat and she is 2 meters longer. Cruises at 14 knots. Modernized inside and very comfortable.”aunt
Reviewing the book cover below, her exterior hasn’t changed much in the last 30 years.
Earlier in the week one of the WW spotters, Alan Sexton, dropped WW a note to say that the 44′ Oliver & Gilpin 1964 built classic wooden launch NAUTILUS was hauled out at Sandspit Marina for some TLC. Always good to see the big old girls being looked after. My lips are sealed but NAUTILUS is another classic woody owned by one of NZ’s yachting ‘royalty’.
The first grouping of photos is as of this week, the b/w photo is probably as launched, and the last lot are from approx. 4 years ago + a peek down below (again 4>5 yrs ago). Forward motion is via twin120hp Isuzu diesel engines.
We understand home these days is the Whangateau area.
The rock bottom pricing continues – the classic wooden launch PANIA is on tme (thanks Ian McDonald) and at last glance the highest bid was $110 and the reserve had been met.
CLASSIC SWANSON KAURI CLINKER LAUNCH – STELLA ROSE
Todays 34’ woody was built in 1967 by boat builder R E Swanson, constructed via the clinker method using kauri planks. The interior is macrocarpa.
Forward motion is from a 70hp Ford diesel engine.
Woody Ian McDonald commented that she had a similar ‘look’ to Baden Pascoe’s – JOHN DORY, I’m sure Baden will disagree 😉
Can we learn more about this Akaroa, South Island woody.
22-06-2025 INPUT EX LIAM DALY There were at least two other ‘almost identical’ clinker built launches built by Bob Swanson. One was named “TELSTAR” And the other named “MANANA” which was often mispronounce! “Mañana” named after a popular song of the day, translated from Spanish means, “tomorrow” or “morning”.Back in the day, Manana was at one time owned by Bay of Many Coves identity Errol Christian. Errol installed a huge turbo charged 100 h.p. diesel engine in Manana which he used as a water taxi throughout Queen Charlotte Sounds.
waitematawoodys.com #1 for classic wooden boat stories, info, advice & news - updated daily - 15+ million views 